内容发布更新时间 : 2024/12/23 23:58:52星期一 下面是文章的全部内容请认真阅读。

方（矩）形管道检验批施工质量验收表

inspection of construction quality test table

机组 工程编号Project number： 性质property： 表4.4.1

分项工程名称 Name of Sub-item project 质量检验结果序号Sr. 检 验 项 目Inspection items 性质property 单位unit 质量标准Quality standard The quality inspection results 应符合现行国家产品标准和设计要求。进口钢材产品质量应符合设计要求和合同规定标准的规定原材料品种、规格、性能 type，1 specifications，performance of raw material 主控main control Products should be consistent with existing national standards and design requirements. Quality of imported steel products should comply with the design requirements and provisions of the standard stipulated in the contract 2 原材料尺寸偏差Size deviation of raw material 原材料表面外观质量The 3 appearance quality of the raw material surface 4 截面边长偏差Cross section length deviation 截面两对角线差 主控5 main control 两端面与轴线垂直度偏差two 6 end face and axis verticality deviation 7 管道长度偏差 管道直线度偏差straightness deviation 对口错边量s.≤10mm 主控main control mm ≤1 mm ≤L2/500，且and≤6 mm 0～L2/500，且and≤10 mm ≤L1/100，且and≤5 mm ≤L1/250，且and≤8 mm 应符合产品标准的规定Should comply with the regulations of the product standard 应符合现行有关标准的规定Should comply with the terms of the current relevant standards ±L1/500，且and≤4 结论conclusion 8 9 分项工程名称 Name of Sub-item project 质量检验结果序号Sr. 检 验 项 目Inspection items 性质property 单位unit 质量标准Quality standard The quality inspection results 结论conclusion align deviation value 表面平面度10 偏差surface flatness deviation 11 s.≤5mm s.＞5mm mm/m s.＞10mm ≤0.1s ≤8 ≤5 加固筋位置偏差strengthening ribposition deviation 内支撑相对于加固筋中心位置偏差 焊接材料的品种、规格、性 mm ≤5 12 mm ≤5 应符合设计要求和现行国家产品 13 能type, specification, performance of welding 焊接 material 焊缝尺寸weld 接头表面质量joint surface quality seam size 焊缝成型weld seam formation 裂纹、气孔和夹渣flaw, crater, blowhole and slag inclusion 主控main control 主控main control 标准的规定Should comply with the design requirements and the provisions of the existing national product standards 应符合设计要求Should comply with the design requirements 焊缝过渡圆滑，接头良好weld seam transits smoothly, and joint well 14 welding 15 16 无no 主控17 严密性 main control 应符合设计要求和现行国家产品油漆的品种、规格、性18 油漆pa19 int 20 能 type ，specifications，performance of paint 涂装前钢材表面除锈remove the corrosion on the steel material before painting 底层防锈漆涂刷apply anti-rust paint at bottom layer 主控main control 标准的规定Should comply with the design requirements and the provisions of the existing national product standards 应符合设计要求和现行国家有关标准的规定should comply with design requirement and provisions of the existing national standards 涂刷均匀、无透底、漏刷paint evenly, and no leakage 无渗漏no leakage 分项工程名称 Name of Sub-item project 质量检验结果序号Sr. 检 验 项 目Inspection items 性质property 单位unit 质量标准Quality standard The quality inspection results 结论conclusion 注：L1为设计边长；L2为管道设计长度；s为管道壁板厚度。L1 is design height; S is pipe wall thickness; 验收结论： Acceptance conclusion 监理单位Supervision unit： 验收单位Acceptance of the unit 施工单位construction unit 监理单位Supervision unit 建设单位Builder unit 签 字signature year年 month 月 day日 year年 month 月 day日 year年 month 月 day日