内容发布更新时间 : 2024/7/6 5:52:25星期一 下面是文章的全部内容请认真阅读。

论文题目：基于直流载波通信的电机调速系统设计与实现

摘 要

本文主要研究了利用MCS-51系列单片机控制PWM信号从而实现对直流电

机转速进行控制的方法。文章中采用了专门的芯片组成了PWM信号的发生系统，并且对PWM信号的原理、产生方法以及如何通过软件编程对PWM信号占空比进行调节，从而控制其输入信号波形等均作了详细的阐述。此外，本文中还采用了芯片IR2110作为直流电机正转调速功率放大电路的驱动模块，并且把它与延时电路相结合完成了在主电路中对直流电机的控制。另外，本系统中使用了测速发电机对直流电机的转速进行测量，经过滤波电路后，将测量值送到A/D转换器，并且最终作为反馈值输入到单片机进行PI运算，从而实现了对直流电机速度的控制。在软件方面，文章中详细介绍了PI运算程序，初始化程序等的编写思路和具体的程序实现。

关键词： PWM信号，测速发电机，PI运算

The Design of Direct Current Motor speed Regulation System Based

On SCM

Hunan Railway Professional Technology College

Abstract

This article mainly introduces the method to generate the PWM signal by using MCS-51 single-chip computer to control the speed of a D.C. motor. It also clarifies the principles of PWM and the way to adjust the duty cycle of PWM signal. In addition, IR2110 has been used as an actuating device of the power amplifier circuit which controls the speed of rotation of D.C. motor. What’s more, tachogenerator is used in this system to measure the speed of D.C. motor. The result of the measurement is sent to A/D converter after passing the filtering circuit, and finally the feedback single is stored in the single-chip computer and participates in a PI calculation. As for the software, this article introduces in detail the idea of the programming and how to make it.

Key words: PWM signal，tachogenerator，PI calculation

1

目录

1. 引言 ............................................................................ 1

1.1 开发背景 ....................................................................................................... 1

1.2 选题的目的和意义 .................................................................................... 1 1.3 研究方法 ....................................................................................................... 2

2. 总体设计概述 ............................................................. 2 2.1 总体硬件电路设计 .................................................................................... 2

2.1.1系统总体设计框图 ................................................................................. 2 2.1.2 8051单片机简介 ................................................................................... 3 2.1.3单片机系统中所用其他芯片选型 ......................................................... 4 2.2 PWM信号发生电路设计 ............................................................................ 7

2.2.1 PWM的基本原理 ..................................................................................... 7 2.2.2 PWM信号发生电路设计 ......................................................................... 8 2.2.3 PWM发生电路主要芯片的工作原理 ...................................................... 9 2.3 功率放大驱动电路设计 ......................................................................... 10

2.3.1芯片IR2110性能及特点 ..................................................................... 10 2.3.2 IR2110的引脚图以及功能 .................................................................. 11 2.4 主电路设计 ................................................................................................ 11

2.4.1 延时保护电路 ...................................................................................... 11 2.4.2 主电路 .................................................................................................. 11 2.4.3 输出电压波形 ...................................................................................... 13 2.4.4系统总体电路图 ................................................................................... 14 2.5 测速发电机 ................................................................................................ 15 2.6 滤波电路 ..................................................................................................... 15 2.7 A/D转换 ...................................................................................................... 15

2.7.1芯片选型 ............................................................................................... 15 2.7.2 ADC0809的引脚及其功能 ................................................................... 16

3. 系统软件部分的设计 .............................................. 16 3.1 PI 转速调节器原理图及参数计算 .................................................... 16 3.2 系统中的部分程序设计 ......................................................................... 17

3.2.1主程序设计 ....................................................................................... 17 3.2.2 PI控制算法子程序设计 ............................................................... 18

4. 系统调试 ................................................................... 19 4.1软件调试 ...................................................................................................... 19 4.2系统仿真 ...................................................................................................... 20

结论 .............................................................................. 21 致谢 .............................................................................. 21 参考文献 ...................................................................... 22 附录 .............................................................................. 23

2