内容发布更新时间 : 2024/12/23 11:31:30星期一 下面是文章的全部内容请认真阅读。
EPON系统ONU互通配置指导手册
-----------------------------------------------------------------------------------------------------------
F/S/P ONT-ID MAC Control Run Config Match LoopBack Flag State State State State ----------------------------------------------------------------------------------------------------------- 0/ 1/0 0 001E-E322-A833 active up config match disable ----------------------------------------------------------------------------------------------------------- In port 0, the total number of ONUs is: 1 In port 1, the total number of ONUs is: 0 In port 2, the total number of ONUs is: 0 In port 2, the total number of ONUs is: 0
注:只有当与红色信息相同的状态时, ONT才算添加成功, 工作状态才正常.
如果不一致,1、请检查ont能力集模板的相关参数;2、检查增加onu时mac地址和实际的mac地址是否匹配;
MA5680T(config)#interface epon 0/1
MA5680T(config)#port 0 tag-based-vlan 使第一个端口支持q-in-q特性!
在0/1/0端口下,将下挂的编号为0的ONT端口为透明传输模式;此种模式下,每个epon口 可以通过下挂的每个ont透传上来256个vlan;
562Ju_MA5680T_1(config-if-epon-0/1)#ont port vlan { portid<0,3> }:0 pon口的编号 { ontid<0,63> }:0 ont的编号
{ fe
{ s-vlanid<1,4094>|transparent
增加业务虚端口
MA5680T(config)#service-port vlan 1196 epon 0/1/0 ont 0 multi-service user-vlan 3001 MA5680T(config)#service-port vlan 1196 epon 0/1/0 ont 0 multi-service user-vlan 3002
1196:外层标签
0/1/0:5680T上的第0个pon口 0:onu的编号;
3001、3002:内层vlan,也就是从楼宇交换机上透传上来的vlan;
第 26 页 共 42 页
26
EPON系统ONU互通配置指导手册
第4章 与UT斯达康OLT互通
4.1 OLT相关信息
4.1.1 BBS4000/BBS1000+图片信息
图 UT BBS4000 OLT
图 UT BBS1000+ OLT
4.1.2 BBS4000/BBS1000+命令行简介
BBS4000与BBS1000+的命令行除个别地方有差异以为基本一致,命令行各个模式及功能如下表描述:
第 27 页 共 42 页 27
EPON系统ONU互通配置指导手册
第 28 页 共 42 页
28
EPON系统ONU互通配置指导手册
4.2 示例拓扑图
InternetPPPoE华华华华Port7 vlan tag 3972ISCOM5108PPPoE华华华华RADIUS华华华华华2 UBRAS华华华华华Optical SplitterGE2/1vlan tag 3972UT BBS4000
Port2 vlan tag 3972ISCOM51044.3 配置步骤 第1步:
打开超级终端,串口参数设置:波特率:11520000bit/s(适用于初始配置)、数据位为8、奇偶校验位为无、停止位为1、数据流控制为无。登入到OLT,进入超级用户模式:
Username:admin
Password:(具体密码需找网络管理员获取) BBS4000> enable BBS4000#
第2步:
将ONU插上电,等ONU系统正常启动以后(系统灯1秒闪烁一次),将ONU连接到OLT上,新的mac地址的ONU会出现告警(每1分钟出现一次,因为非法注册静默时间是1分钟)
Alarm onu reg rej send to trap, module 1, olt 3, mac=00:0e:5e:04:8d:13(pal_alarm.c, pal_evt_handler_onu_reg_rej, 450)
第3步:
显示olt的信息;
BBS4000# show int epon-olt b
OLT state admin phy mac ONU transceiver self-diag Hardware Firmware id state state addr num type state version version ------------------------------------------------------------------------------------------------------------
1/1 Running Enabled present 00:e0:8e:88:01:00 29 EPM04B-SFP passed 0x20 0x30200
第 29 页 共 42 页 29
EPON系统ONU互通配置指导手册
1/2 Running Enabled present 00:e0:8e:88:01:00 17 EPM04B-SFP passed 0x20 0x30200 1/3 Disabled Enabled present 00:e0:8e:88:01:00 0 EPM04B-SFP passed 0x20 N/A 1/4 Disabled Disabled present 00:e0:8e:88:01:00 0 EPM04B-SFP passed 0x20 N/A 2/1 Disabled Disabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A 2/2 Disabled Disabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A 2/3 Disabled Disabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A 2/4 Disabled Disabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A
解析:第一块板的1pon口 和2pon口是在跑业务的,其他的pon口没有用;
显示系统配置信息;
BBS4000#config terminal
BBS4000(config-t)# show pon-sys PON system global parameters:
local sla authentication = enabled
local logical port strict binding = enabled MAC Address Aging Timer = 300 seconds
remote-mgmt onu-authentication time out = 10 oam timeout = 10000 ms
loopback detection interval time = 1 minutes
解析:本地sla认证开启,本地逻辑端口绑定开启;
第4步:
开启第2板上的第1口pon口,如果是在已开启的pon口上加新的onu此步可以省略;
BBS4000#config terminal
BBS4000(config-t)# interface epon-olt 2/1 BBS4000(config-t-if-olt-2/1)# no shutdown 开启2板上的1pon口 BBS4000(config-t-if-olt-2/1)# BBS4000(config-t-if-olt-2/1)# ex
BBS4000(config-t)# show interface epon-olt brief 查询是否开启
OLT state admin phy mac ONU transceiver self-diag Hardware Firmware id state state addr num type state version version ------------------------------------------------------------------------------------------------------------
1/1 Running Enabled present 00:e0:8e:88:01:00 29 EPM04B-SFP passed 0x20 0x30200 1/2 Running Enabled present 00:e0:8e:88:01:00 17 EPM04B-SFP passed 0x20 0x30200 1/3 Disabled Enabled present 00:e0:8e:88:01:00 0 EPM04B-SFP passed 0x20 N/A 1/4 Disabled Disabled present 00:e0:8e:88:01:00 0 EPM04B-SFP passed 0x20 N/A 2/1 Disabled Enabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A 2/2 Disabled Disabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A 2/3 Disabled Disabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A 2/4 Disabled Disabled present 00:e0:8e:88:02:00 0 EPM04B-SFP passed 0x20 N/A
BBS4000(config-t)# show interface epon-olt 2/1 brief
第 30 页 共 42 页
30