内容发布更新时间 : 2024/12/23 11:14:12星期一 下面是文章的全部内容请认真阅读。
毕业设计说明书
简易冲床
学生姓名: 学号: 学 院: 专 业: 指导教师:
年 月
简易冲床设计
摘 要
本次我设计的是简单冲裁模具。因为本次设计题目与实践结合紧密,经过查阅资料,首先要对零件进行工艺分析,经过工艺分析和对比,采用冲孔落料工序,通过冲裁力、顶件力、卸料力等计算,确定压力机的型号。再分析对冲压件加工的模具适用类型选择所需设计的模具。得出将设计的模具类型后将模具的各工作零部件设计过程表达出来。
在本次设计中采用了冲孔、切断级进模。该模具的特点是在排样过程中不用考虑搭边值,板料宽度与零件宽度一致,节约材料。同时简化了步骤,提高了工作效率。
关键词:冲压,冲孔,落料,压力机
Simple Blanking Die Design
Abstract
I designed this simple blanking dies. Because the design of the close combination of Title and Practice, after access to information, the first parts to the process analysis, through process analysis and comparison, the use of punch blanking process, through the blanking force, the top piece, and in terms of discharge power, to determine the model press. Further analysis of the stamping dies for processing the application to select the desired type of mold design. The mold will be designed to draw upon the type of the working parts of the mold design process to express.
In this design the use of the punching, progressive die off. The characteristics of the mold are in the process of packing up side without considering the value of sheet width and the width of the same parts, saving material. At the same time simplifying the steps to improve the work efficiency.
Keywords: Stamping, Punching, Blanking, Press
中北大学2009届毕业设计说明书
目 录
1 引言 .................................................................. 1 2 冲裁模具的工艺分析 .................................................... 2 2.1 冲裁件工艺分析 ..................................................... 2 2.2 工艺方案的确定 ..................................................... 2 2.3 冲裁变形过程 ....................................................... 3 2.4 冲裁间隙 ........................................................... 3 3 模具设计的计算 ........................................................ 5 3.1 排样 ............................................................... 5 3.2 搭边值的确定 ....................................................... 5 3.3 条料宽度的确定 ..................................................... 6 3.4 材料利用率的计算 ................................................... 7 3.5 冲压力计算 ......................................................... 7 3.5.1 冲裁力 .......................................................... 7 3.5.2 冲孔力 .......................................................... 8 3.5.3 冲裁时的推料力 .................................................. 8 3.5.4 冲压力的计算: ................................................... 8 3.6 确定模具压力中心 ................................................... 9 3.7 冲模刃口尺寸及公差 ................................................. 9 3.7.1 冲孔部分 ........................................................ 9 3.7.2 落料部分 ....................................................... 11 3.8 各主要零件结构尺寸的确定 .......................................... 12 3.8.1 凹模外形尺寸的确定 ............................................. 12 3.8.2 凸模长度LP的确定 ............................................... 12 3.9 定位零件 .......................................................... 13 4 冲压设备选取 ......................................................... 14 5 模具的装配 ........................................................... 15 5.1 设计并绘制总图、选取标准件 ........................................ 15
第 I 页 共 II 页
中北大学2009届毕业设计说明书
5.2 组装 .............................................................. 16 5.3 试模 .............................................................. 17 6 绘制部分零件图 ....................................................... 19 7 结论 ................................................................. 22 附录A ................................................................... 23 附录B ................................................................... 24 附录C ................................................................... 25 参考文献 ................................................................ 26 致谢 .................................................................... 27
第 II 页 共 II 页